Special steel waterproof adhesive plastic mud clay reinforced plastic (plastic clay) is a two-component structural plastic multifunctional reactive polymer materials, milky gel, non-toxic, tasteless. PVC plastic (plastic clay) is A, B two sticks were mixed, cured hard as porcelain, tough structure, with ceramic characteristics: wear, scrub, anti-acid, corrosion resistance, high (low) temperature , does not shrink, not aging, deterioration, non-toxic, good insulation, waterproof, moisture and so on. PVC plastic (PVC mud) with high adhesion strength, tough structural strength, 100% waterproof, moisture, mildew main purposes: 1, waterproof the building, sealing, crack filling and outside walls, tile cracks, shedding and other fixes. Larger area crack repair, crack repair stone tile, marble and stone repair and other specialty; 2, steel anchorage (anchorage glue); 3, between the wall seepage closed, concrete, bricks, tiles and permanent bonding waterproof treatment, door window glass bonding, never change, aging; 4, suitable for hotels, restaurants, apartments, home, etc. toilet, basin, gas stove, sun room, shower, bath, bay windows, countertops , throughout the surrounding frame and corner waterproof, decoration. Use plastic mud on the side seam after treatment (Note: the color according to your requirements modulation), can be modified to form a wall around the edge of the whole surface smooth and bright, hard as porcelain, does not harbor dirt, and a separate line, water impermeability, mildew, is a kind of fashion elements, fashion, beauty, elegant line of high-end decorative materials. 5, a variety of different materials of ceramic, metal, wood, hard plastic, glass, concrete, all kinds of stone (stone for plastic), composite materials bonded to each other, setting fast time, firmly bonded, waterproof, anti-aging; 6 , steel and metal bonding, high temperature resistance, repair cracks and other metals; 7, installation of water, pipe fittings (pipe, tube, pipe and pipe fitting), various types of containers (body sheet metal, engine crack, exhaust pipe , fuel tanks, water tanks, plating tank) patch plugging fixed. 8, bonding furniture, ceramics, wood, plastic, metal, stone and other appliance repair. 9, parts, pipes, fixed line, connecting, sealing and insulation corrosion. 10, sanitary ware, kitchen equipment installation, fixed and repaired. At present, many cases are with glass, plastic, glass, plastic but a long time will be moldy, black, flaking, not only unsightly, but also leaking. Can completely replace the plastic glass. 11, water trap and embalmed ships, underwater equipment. 12, the production of various shapes of parts mold, manufacture sculptures, toys and models. Physical and chemical properties before use for clay-like, after curing, as hard as steel. This product is a two-component reactive macromolecular materials, stable performance. A, B groups were mixed after 40 minutes began to solidify, 24 hours after completely hardening. Health and hazards of the product is environmentally friendly materials. Tasteless, non-toxic, non-irritating, non-flammable non-explosive, stable performance. Direct contact with the skin can. After the manual operation can be directly cleaned with water to hand. Packing 1000G / group (A + B) Use 1, before construction to completely remove loose objects attached to the surface structure, such as glass, plastic and other moldy. Preferably the bonded surface roughening treatment. 2, the construction of surface water will be slightly moist. 3, A, B two doses to take the same amount (1: 1 ratio) fully mixed, if the material is too dry or left the desirability of a small amount of water, rub, can not add too much water, otherwise it will affect the bonding effect. 4, the construction of planned amount of materials needed for construction, A, then B must run good material mixed .40 minutes after beginning to solidify within 30 minutes, 24 hours after the maximum hardness. (You can also adjust the curing time of construction according to customer special requirements of the construction) 5, after the construction of the surface water on hand or tool to push the flat trowel and apply a pressure to enhance the adhesion effect, such as the need to accelerate the curing can be properly heated. 6, the operation is completed, the water or soapy water to clean your hands and tools. Notes 1, should be used to avoid contamination to other objects and clothing, such as accidentally contaminated should be cleaned with water as soon as possible, difficult to remove after cure. 2, the remaining portion of the material is not used, can not be A, group B were mixed, A, B material should replace all the original packaging tank. Preservation should avoid high temperatures. Related Keywords: plastic mud | plastic clay manufacturers | plastic mud Brand | Plastic mud Price | plastic mud Wholesale | architecture steel mud | New steel mud | ceramic steel mud